How To Install Rear Window Tint Film

Step 1 Prep Work.

How to install rear window tint film. For those whod like a general understanding on how window tint is applied this video on window tint installation will provide some great information. Well now that our window film has been applied to the glass next step that we are going to have to go through is to go ahead and squeegee all the water out. Anchor the film onto the window along the h shape. Wet the outside of the window with the application solution.

As the saying goes prep work makes the dream work. Let a professional tint your windows. Fortunately modern high-quality window tint is very malleable so skilled technicians have no problem getting the tint to stick properly around all those pesky wires. Squeegee top of the film to the glass.

Squeegee the film onto the window pushing bubbles out to the edges. OK there are 2 ways to tint the rear window. Tint just the lower portion of it so that the top roof part is not tinted as it already has the Tesla factory tint. The problem with that is that with time air will get in between those seams and the seam will become visible and ugly.

Professional look and easy to install. In this installation segment well be showing you how to install window film on the rear window using the most commonly used Wet Shrink Technique. Tint the entire rear window glass. Press firmly on squeegee to remove ALL.

The tint is applied on the inside of the windows you may work the window film on the outside. Stick the film to the windows interior leaving 18 to ¼ inch 3 to 6 centimeters at the top of the window. The rear window tinting film will usually come in 2 or more pieces for ease of installation. Roll the film liner side facing out onto the glass keeping in mind that the tint will be applied to the interior side of the glass.

Gently run the razor blade under the film little by little until the full square around the damaged area has been removed. From the middle outward follow the actual defroster lines. Place your tint onto the outside rear window surface with the transparent plastic sheet facing outwards. Trim away the excess film and set the remaining roll to the side.

If you are just starting out and wondering what the most suitable tools are for the job we have created a window tint fitting kit to get you started. While applying the tint to any window it is very important to make sure the films dont trap any air. Use your Blue Max Squeegee start from the middle of the actual window and work your way outward. Use a heat gun to shape the film to the exact size and shape of the window.

Click here to find out more. Secure the Black Magic window tint film to the frame with masking tape. Cut the tint film with a razor knife to get a sharp edge. This is especially important when applying a new window film tint to your car truck or SUV.

Window tint for cars. It may look ugly. The raised wires on rear windows makes this especially challenging. Now you have a shape that will fit the window but double check the film by placing it over inside of the window.

Press gently down on the film to temporarily hold it in place for trimming. Follow the lines of the window frame to cut as precisely as possible and round off the corners to prevent peeling and dog ears. Then taking your time start applying the tint inch by inch starting at the bottom. Please note that when you separate the tint from the transparent sheet unless your fingers are wet permanent fingerprints can be left on the glue surface of the tint.

Window TintingLearn how to tint harder. Try to keep your fingers moist when handling tint. Well cover everything from rough cut patterns. The new tint needs to be the same shade as the old material.

This will show a line where the edge of the tint is. More help can be found on the window tinting forum. Learn How to Install a Film that you have previously Heatshrinked in part 1 of this video. Cut the tint film 1 inch wider than the width of the window.

Slip the bottom of the film underneath the window gasket. Make sure to clean the window of any dirt and dust before you apply new tinted film. Once youve applied the tint grab some warm water in a bottle and spray the window. On curved glass squeegee from the center to the bottom then squeegee film toward the sides.

Next lay the window film down with the liner side up. Next create an anchor by dampening in an h shape. How to install a pre-cut fixed side window tint also use this method for installing pre-cut sun strips Experience level. When you have a working template lay both it and the film on a firm surface and use a sharp Exacta or similar knife to cut along the edges so that the cut film exactly matches the shape of the template.

First put the application spray on the window youre about to tint. Cut the tint film 1 inch longer than the height of the window. You want to ease it on from the edges to avoid any bubbles. Remember youll need to wind down the window slightly to make sure the film is cut to the right shape.

If you are looking for How To Install Rear Window Tint Film you've reached the perfect place. We ve got 15 images about how to install rear window tint film adding images, photos, photographs, backgrounds, and much more. In these web page, we additionally provide variety of graphics available. Such as png, jpg, animated gifs, pic art, symbol, black and white, translucent, etc