How To Tint Your Rear Car Window

There are several reasons why rear windows with defroster wires can be difficult to tint but its no problem for an experienced shop with high-quality films.

How to tint your rear car window. Now you can cut the tint into the sizes that you measured for each individual window. Roll your window down 1-2 inches 25-5 cm and hold your tint up against the corner of the window with the adhesive facing the window. Film Application Solution. Peel Off Liner and Apply Tint Film to Inside of Car Window Alright now the exciting part.

Or view the Entire Range you can choose from. Follow the lines of the window frame to cut as precisely as possible and round off the corners to prevent peeling and dog ears. This can be easily done by putting masking tape on one side of the tintliner sheet and pulling the two apart. Short video on how to remove window tint and more importantly the glue thats left on your window.

And if youre looking to remove and replace old tint ask us about window film trade-in for a special deal on your next tint. If you tint your rear window too dark youll end up having to rely on your side mirrors. Replace your tint with one of our tints. On the highest setting blast the corner of the window with the hairdryer until the heat causes the tint to curl in the corner.

Clean the inside of the car well to make sure any dust and dirt isnt floating around in the air when you apply the tinting vinyl. It may look ugly. Now you have a shape that will fit the window but double check the film by placing it over inside of the window. Clean the interior side of the window with soapy water and a razor blade so theres nothing on it that could interfere with the tint.

Please note that when you separate the tint from the transparent sheet unless your fingers are wet permanent fingerprints can be left on the glue surface of the tint. The back window is the hardest to tint because of the curvature of the glass but this video takes you through it step by step so pay attention and you should get it right. Now that you have the window tint cut out in the general size and shape of your car window remove the liner from the tint itself. To have your tint removed the right way speak to your local Tint a Car dealer.

As is the case with the windshield tinting your rear window isnt the simplest process. With the help of your assistant to hold the film in place you will be able to do any trimming to make sure the film will fit properly but make sure you cut right into the corners to avoid ending up with gaps between the rubber seals and the film. Place your tint onto the outside rear window surface with the transparent plastic sheet facing outwards. First two items that you need is your water bottle and a bounty fabric softener.

People often ask us if it is possible to successfully tint over rear defroster wires. Tint just the lower portion of it so that the top roof part is not tinted as it already has the Tesla factory tint. Before you cut your film to place on the window you want to be sure there is at least 2 inches around each end of the window. Make sure you have enough for your front and rear windows while allowing an extra 2 inches than you measured for each window.

Tihs is a tutorial on how to tint a car side-window using window tint film spray bottle rubber squeegee single-edge razor blade or utility knife distille. Spray the inside of the window with soapy water one more time once youre done. Discard the protective liner and remove the film from the outside of the window and place it on the inside of the window. It is best to install window tint when the car is away from the road in a well-lit garage if possible but if that isnt an option just make sure it is a clear dry day.

Your rear window allows you to see whats going on behind you when youre on the road. Spray a little bit of soap and water on to it and go ahead and smear the window with the actual fabric softener. This will allow you to carefully peel away the layer of tint. In todays segment of Tint Your Ride I am going to show you how to apply and dry shrink a rear window.

Try to keep your fingers moist when handling tint. Use a heat gun to shape the film to the exact size and shape of the window. The sharper the blade the sharper the finish. This will show a line where the edge of the tint is.

Most botched window tint jobs take place on the rear window. Remember that the tint film goes on the inside of the window so check that the film fits properly since the outside and inside. OK there are 2 ways to tint the rear window. The short answer is yes you can.

Remember youll need to wind down the window slightly to make sure the film is cut to the right shape. Ensure that you have an extension cord ready so that you can reach the car with your hairdryer. Tinting Your Rear Window. Also known as tint slime when added to water gives you a soapy solution essential for applying your window tint.

In order to get that perfect looking tint on your windows you will need the following.

If you are searching for How To Tint Your Rear Car Window you've arrived at the right place. We ve got 15 graphics about how to tint your rear car window adding pictures, photos, pictures, backgrounds, and more. In such page, we additionally have number of images out there. Such as png, jpg, animated gifs, pic art, symbol, black and white, translucent, etc